Monthly Archives: March 2025

　　01Even so, air conditioning for commercial We must also adhere to the quality of the industry and create unique products for the company. https://puremind.com/product-category/puremind-air-conditioner/commercial-air-conditioner/

　　

　　If you leave home for a day …

　　

　　Kureczka said: “If you just leave home for one day, it is more energy-saving to turn on the air conditioner, but you should raise the temperature by several degrees instead of keeping the comfortable temperature set at home.”

　　

　　If the house is unoccupied for only a day or two, the same direction applies.

　　

　　It’s not necessarily a bad thing to turn off the air conditioner during the day. Either way, the speed of the air conditioner is the same-it just takes longer to cool the hot space. In fact, if you drive at normal temperature all day, you may consume more energy than if you turn it off and have a meeting at night.

　　

　　Air conditioning is not only to cool the space, but also to greatly reduce the humidity level. When the air conditioner is turned off for more than a few hours, the humidity level begins to rise, which may easily lead to mold growth, damage to electronic products, and warping and deformation of wood products. In addition, pets left at home may also be at risk of overheating and discomfort, which may occur especially in hot and humid climate.

　　

　　This is why it is suggested to turn on the air conditioner, but turn up the temperature. The U.S. Department of Energy pointed out that higher indoor temperature will actually slow down the flow of heat into the house, thus saving energy and money.

　　

　　When you get home, don’t turn the air conditioner down too low to “speed up” the cooling process, so that the room won’t get cold faster, and it will only increase energy consumption (cost money).

　　

　　02

　　

　　If you leave home for more than two days …

　　

　　If the whole family (including pets) has been away from home for more than two days, the equipment can be turned off. Kureczka said, “Turn off the air conditioner, and you can save a lot of energy and bills.”

　　

　　This means that when you come back, the temperature inside the room may not be very good and you will feel stuffy. Kureczka suggested, “Installing an intelligent thermostat is a good way to monitor and control the energy efficiency of your home, even if you are not at home-you can turn up the temperature before you leave and then turn it down on your way home.”

　　

　　She also suggested that if you go out for more than a few hours, please close the curtains, which can effectively block the sun, so that the air conditioning unit does not have to work so hard. Especially in areas with extreme temperatures, this will make a huge difference.

　　

　　03

　　

　　At home …

　　

　　The US Department of Energy and the Environmental Protection Agency suggest that the thermostat should be set to 26≧ or higher during the day, 28≧ when sleeping and 29≧ when going out.

　　

　　Think this setting temperature is too high? When the temperature is reduced to 26≧, compared with 22≧, it can save 25% of the electricity bill.

　　

　　Kureczka said: “It varies from person to person to adjust the temperature as high as possible while maintaining comfort. Generally speaking, increasing the temperature by 1 C will help reduce the cooling cost by 5%. “

　　

　　If it is acceptable to adjust the temperature higher than you are used to, then other measures may also make you feel comfortable, such as using ceiling fans. But the ceiling fan will not change the temperature, so remember to turn off the electric fan when you leave the room. Otherwise, you have to pay unnecessary electricity bills.

　　

　　Finally, try to ensure that the house is insulated, so that cold air will not escape and hot air will not sneak in.

In the eyes of industry experts, cnc machining services Indeed, it has great development potential, which makes many investors more interested. https://www.ultirapid.com/services/cnc-machining/

The medical profession in South Korea has been playing a game with the government for more than half a month, the general election is just around the corner, and the doctors’ strike is escalating.

According to Yonhap news agency quoted by the Global Times, 430 professors from Seoul University School of Medicine attended the meeting on the 11th to issue an ultimatum: if the government does not come up with a sincere and reasonable solution to the situation of interns and residents’ collective resignation, all professors will submit their resignations on the 18th. South Korean media commented that the medical front line is likely to fall into greater chaos.

The South Korean government does not intend to compromise, and responded on the 12th, expressing serious concern about this. South Korean President Yoon Yue issued a directive on the 12th, calling for the rapid promotion of health care reform measures, including expanding the enrollment of medical schools, in accordance with the principles.

In addition, the South Korean government has sent license revocation notices to nearly 5000 doctors who refused to return to work, and decided to send 20 military medical officers and 138public health doctors to 20 hospitals from the same day to meet their urgent needs.

With the intensification of aging, the demand for medical resources in Korean society is increasing day by day. The South Korean government announced plans to expand the enrollment of medical students in early February: the enrollment of medical schools in colleges and universities increased from 3058 at this stage to 5058 in the 2025 academic year. According to South Korean health authorities, if the current enrollment scale remains unchanged, there will be a shortfall of 150000 South Korean doctors by 2035.

But the plan to expand enrollment has drawn strong opposition from doctors’ groups and medical students. They believe that the move will lead to excessive health care, strain the funding of the health care system, and lead to a decline in the quality of medical education. Moreover, South Korea lacks the mechanism to regulate the choice of departments for medical graduates, and blindly increases the number of medical students, which will lead to the accumulation of medical resources in big cities. Some medical staff are also worried that the plan to expand enrollment will lead to a reduction in the income of doctors.

Recently, medical professors at a number of South Korean universities are planning to resign collectively. On the 7th of this month, the Emergency response Committee of the Association of professors of Ulsan University Medical College agreed that the professor would submit his resignation on his own. The Association of Professors of Yonsei University School of Medicine set up an emergency response committee on the 12th, and the Association of professors of Cheng Junkuan University School of Medicine held a meeting on the same day. The School of Medicine of Katuli University will meet this week to discuss whether to take collective action.

In response to the possible collective resignation of medical professors, Oval Office officials insisted that since the president demanded rapid progress in accordance with principles, even professors were no exception for collective actions that left the front line of health care in violation of the Medical Law.

As of the 11th, the South Korean government has sent advance notice of administrative sanctions such as revocation of medical licenses to 5556 interns and residents who have left their posts.

Cao Guihong, head of South Korea’s Ministry of Health and Welfare, said at a meeting on the 12th that the decision of the professor’s collective resignation from the Medical College of Seoul University threatened the lives and health of patients, and that the government would do its utmost to maintain the emergency diagnosis and treatment response system and solve the problem of disorder in the medical scene. He called on professors to protect the lives of patients and work with the government to bring outgoing internships and residents back to the medical front line.

On the 12th, the faculty of Seoul University School of Medicine proposed a compromise. They held a press conference in the Korean National Assembly, saying that both the government and the Korean Physicians Association should abandon their inherent position and entrust overseas authorities and institutions recognized by all parties to analyze South Korea’s health and medical indexes. and according to the results of the analysis to decide whether to increase the number of medical school enrollment, at the same time to build a dialogue mechanism with the participation of the government, medical association, government and opposition, national representatives, professors, internships and residents. Formulate practical basic medical, community and public health policies in the coming year.

However, according to Yonhap news agency, an official from the South Korean President’s Office confirmed on the 12th that the plan to expand the enrollment of medical schools by 2000 students a year will not be adjusted. This figure is scientific, and the government’s determination to promote health care reform has not changed.

Less than a month before South Korea’s parliamentary election on April 10, South Korea’s ruling party has regained a lot of support for its policy of expanding enrollment in medical schools. The results of an opinion poll released by Gallup in South Korea on March 8 showed that the good rate of President Yoon Yue’s administration performance was 39%, and the bad rate was 54%. As for the reasons for praise, the answer to the expansion of medical school enrollment accounted for the largest proportion, accounting for 28%, followed by prompt decision, courage and perseverance (9%). According to an opinion poll released by the agency on February 23, Yin Yue’s good evaluation rate was 34%, and the poor evaluation rate was 58%.

For this protracted standoff, some Japanese media commented that the demand for reconciliation in South Korea is growing day by day. Doctors and the government should not be in the boxing ring. People’s patience is disappearing. We must find a way out of this quagmire through dialogue.

More importantly, put cnc machining services It is imperative for us to make thorough analysis and maximize its social function. https://www.ultirapid.com/services/cnc-machining/

According to Agence France-Presse reported on March 19, Russian official media confirmed on the 19th that Russia has replaced its commander-in-chief of the Navy. Earlier reports said that Nikolai Evmenov was dismissed as commander-in-chief of the Navy because Black Sea Fleet warships were repeatedly attacked and damaged by Ukraine.

Reported that according to RIA Novosti, former commander of the Russian Northern Fleet Alexander Moiseyev has been appointed acting commander-in-chief of the Navy, replacing Nikolai Evmenov, who has served as commander-in-chief of the Navy since May 2019.

RIA Novosti reported: Moiseyev was introduced as acting commander-in-chief of the Russian Navy at a ceremony.

Reported that the Kremlin declined to comment on Moiseev’s appointment last week. This marks the largest reshuffle of the Russian military’s top ranks in months.

According to reports, the Ukraine military claims to have destroyed more than 20 Russian ships since the conflict began in February 2022, including a military patrol boat earlier this month.

Reports said that these attacks embarrassed Moscow and forced it to transfer ships from the Sevastopol naval base in Crimea to the port of Novorossiysk further east. (Compiled by Liu Xiaoyan)

　　What is a fixed-frequency air conditioner? The grid voltage in China is 220 volts and 50 hertz, and the air conditioner working under this condition is called a fixed-frequency air conditioner. Because the power supply frequency can’t be changed, the rotating speed of the compressor of the traditional fixed frequency air conditioner is basically unchanged, and the indoor temperature can be adjusted by constantly “turning on and off” the compressor, which is easy to cause the room temperature to be hot and cold and consume more electricity.With the expanding influence of the industry, commercial ac unit Our business is also constantly spreading, and the development of the market is also gradually advancing. https://puremind.com/product-category/puremind-air-conditioner/commercial-air-conditioner/

　　

　　What is a variable frequency air conditioner? The main engine of the variable frequency air conditioner automatically performs stepless speed change, and it can automatically provide the required cooling (heating) amount according to the room conditions. When the indoor temperature reaches the expected value, the air conditioning main engine will run at a constant speed that can accurately maintain this temperature, so as to realize “non-stop operation”, thus ensuring the stability of the environmental temperature.

　　

　　Advantages and disadvantages analysis:

　　

　　Advantages of fixed frequency air conditioning: affordable price, more options, rich products and various types.

　　

　　Disadvantages of fixed frequency air conditioning: Relative temperature control and energy saving are still slightly inferior to frequency conversion.

　　

　　Advantages of inverter air conditioner: more accurate temperature control, low temperature, wide voltage start, and more energy saving.

　　

　　Disadvantages of inverter air conditioner: the relative price positioning is higher, while the affordable inverter is less optional.

　　

　　To sum up, it is obvious that inverter air conditioners are smarter! But the price will naturally be more expensive.

precisely because cnc turning service The rapid development of, so also brought new opportunities to the industry. https://www.ultirapid.com/services/cnc-machining/

Abidjan, July 14 (Reporter Zhang Jian) News from Niamey: Niger’s Defense and Security Forces issued a communiqué on the evening of the 13th, saying that most of the dozens of prisoners who recently escaped from the country’s Kutukare prison have been captured and three others were killed.

The communiqué said the area where the prison is located has been cordoned off and an aerial search operation is still underway to find the remaining fugitives. The military called on the public to be vigilant and immediately report any suspicious person or any relevant information to the authorities.

On the evening of the 11th, a prisoner escape occurred at Kutukare Prison in Tirabei Province, Tirabei Region, western Niger. The prison is located 50 kilometers northwest of Niamey, the capital of Niger, and holds members of extremist organizations such as the Boko Haram Islamic State. In 2016 and 2019, two jailbreaks occurred in this prison, both of which were successfully prevented.

　　There are many kinds of refrigeration methods, such as gas expansion refrigeration, liquid gasification refrigeration, vortex tube refrigeration and thermoelectric refrigeration. Among them, liquid gasification refrigeration is the most widely used, and its working principle is to realize refrigeration by using the heat absorption of liquid gasification.This means that inverter hvac system It is the weather vane of the industry and can bring people great self-confidence. https://puremind.com/product-category/puremind-air-conditioner/split-air-conditioner/

　　

　　1, the working principle of air conditioning (mainly refrigeration, heating on the contrary):

　　

　　The high-temperature and high-pressure refrigerant discharged from the compressor flows through the outdoor heat exchanger through the four-way valve, and dissipates heat to the outdoor air through heating transfer, and the refrigerant changes from gaseous state to liquid state-throttles and depressurizes through capillary (or solenoid valve)-one-way valve-filter-two-way valve (outdoor high-pressure pipe)-enters the indoor heat exchanger to absorb heat (realize refrigeration)-outdoor three-way valve (outdoor low-pressure pipe). Complete a single-loop refrigeration cycle.

　　

　　2. Types of components in refrigeration system:

　　

　　The air conditioning refrigeration system is mainly composed of four parts and some auxiliary equipment in the refrigeration system.

　　

　　The four major pieces are:

　　

　　compressor

　　

　　condenser

　　

　　Throttle mechanism

　　

　　Evaporator composition.

　　

　　Auxiliary equipment:

　　

　　Oil separator;

　　

　　Drying filter;

　　

　　Liquid storage tank;

　　

　　Electromagnetic four-way reversing valve;

　　

　　Solenoid valve; Check valve

　　

　　3, the working principle of each component

　　

　　Compressor: As the “heart” of refrigeration system, it has an important influence on the performance, noise, energy consumption, vibration and service life of air conditioning. According to the principle of thermodynamics, it can be divided into volumetric type and velocity type.

　　

　　Volumetric type: a certain volume of gas is sucked into the cylinder and the internal volume of the cylinder is changed to realize gas compression and forced discharge.

　　

　　Speed type: make the inhaled gas get a certain speed, and then slow down, so that kinetic energy can be converted into pressure energy and then discharged. The growth of gas is converted from speed.

　　

　　one

　　

　　Scroll compressor: It is formed by meshing two vortexes of stator and rotor.

　　

　　Rotor compressor: it consists of spindle with eccentric wheel, cylinder, sleeve, air inlet, slide plate, spring, exhaust valve and exhaust port.

　　

　　Condenser: The condenser transfers the refrigerating capacity of the evaporator in the refrigeration system to the environmental medium (cooling water or air) together with the power consumption of the compressor. According to cooling, it can be divided into air-cooled type, water-cooled type and evaporative type. When cooling, it mainly radiates heat to the outside, and when heating, it absorbs heat to the outside.

　　

　　Evaporator: The main function of the evaporator is to boil and evaporate the low-temperature and low-pressure refrigerant liquid that has entered the throttle in the evaporator, absorb the heat of the cooled medium, and then become low-pressure saturated (usually overheated) vapor itself, which is continuously sucked away by the compressor. In other words, the evaporator is a heat exchange device that absorbs heat (that is, outputs cold energy).

　　

　　Throttle element: Throttle element is one of the four main elements in the refrigeration system. Its main function is to throttle and reduce the pressure of high-pressure liquid refrigerant, ensure the pressure difference between condenser and evaporator, and make the refrigerant entering the evaporator absorb heat and evaporate at the required low pressure, thus achieving the purpose of refrigeration and cooling. Adjust the refrigerant flow into the evaporator to adapt to the load change of the evaporator and make the system run normally.

　　

　　Capillary: It is a very thin tube, usually with an inner diameter of 0.5 ~ 2.5 mm and a length of 1 ~ 5 m.. When the refrigerant flows in the tube, it is necessary to overcome the resistance in the tube, which naturally produces a certain pressure drop.

　　

　　Capillary characteristics: Because it is in the normally open state, when the compressor stops, the high and low pressure can be quickly balanced, which is conducive to the compressor starting again. Simple structure, convenient manufacture and low price. For the heat pump system, there is no import and export problem in the throttling process of refrigerant in capillary [this article source: refrigeration encyclopedia WeChat official account” target=_blank>. Using capillary refrigeration system, the performance of the unit is very sensitive to the refrigerant charge. When the operating conditions of the refrigeration system change, the capillary tube has poor ability to adjust the refrigerant flow. Due to the small inner diameter of capillary and long pipeline, it is easy to be blocked, so attention should be paid to the drying and cleaning of the system. Generally, a dry filter is set in front of the capillary to prevent clogging.

　　

　　Thermal expansion valve: the regulating valve that controls the liquid supply of evaporator, and it is also the throttle valve of refrigeration device. Thermal expansion valve uses the change of superheat of refrigerant at evaporator outlet to adjust the flow. According to different structures, it can be divided into internal balance type and external balance type.

　　

　　Disadvantages of thermal expansion valve: low control precision and limited adjustment range. The diaphragm deformation of valve body is limited, which makes the change range of valve needle opening smaller, so the adjustment range of flow is small. When large flow regulation is required, it cannot be met. The high-temperature gas at the place where the signal feedback has a lag evaporator must first heat the shell of the temperature sensor, which has a large thermal inertia, leading to the lag of the reaction.

　　

　　2

　　

　　Electronic expansion valve: the application of electronic expansion valve overcomes the shortcomings of thermal expansion valve and provides conditions for the intelligence of refrigeration device. The electric signal generated by adjusting parameters is mainly used to control the voltage or current applied to the expansion valve, so as to achieve the purpose of adjustment, so that the control system of the electronic expansion valve is complicated and the price is high.

　　

　　Electronic expansion valve classification:

　　

　　Electromagnetic electronic expansion valve;

　　

　　Electric electronic expansion valve.

　　

　　4. Auxiliary equipment of refrigeration system

　　

　　Oil separator: The high-pressure gas (gaseous working medium and lubricating oil) from the compressor enters the oil separator to separate the lubricating oil from the working medium gas and flows down along the inner wall of the cylinder. The working gas is led out of the oil separator from the central pipe through the porous baffle. The separated lubricating oil is concentrated in the lower part of the oil separator and can be discharged regularly, or the lubricating oil can be automatically returned to the crankcase of the compressor by using the ball valve.

　　

　　Drying filter: The function of drying filter is to absorb moisture in refrigeration system, prevent impurities in the system from passing through, and prevent the pipeline of refrigeration system from being blocked by ice and dirt. Because the most easily blocked part of the system is the capillary (or expansion valve), the drying filter is usually installed between the condenser and the capillary (or expansion valve).

　　

　　Liquid storage tank: During the operation of the refrigeration system, the circulating amount of refrigerant in the system will change due to the change of working conditions or the adjustment of refrigeration capacity. Setting the liquid storage tank can balance and stabilize the refrigerant circulation in the system by using the liquid storage capacity of the liquid storage tank, so that the refrigeration system can be in normal operation. In addition, when a component in the refrigeration system fails and needs to be dismantled and repaired, the system refrigerant can be recovered to the liquid storage tank through certain operation methods.

　　

　　The liquid storage tank is generally arranged between the condenser and the throttling element, so that the refrigerant liquid in the condenser can smoothly enter the liquid storage tank. The position of the liquid storage tank should be lower than that of the condenser.

　　

　　Electromagnetic four-way reversing valve: after the electromagnetic coil is energized, it changes the action direction of the valve block in the valve body and changes the flow direction of the refrigerant. So as to achieve the purpose of cooling or heating.

　　

　　three

　　

　　Solenoid valve: Solenoid valve is usually installed in front of the expansion valve to directly control the amount of refrigerant entering the evaporator. It can also be installed before the compressor unloading cylinder to control the unloading of the compressor cylinder.

　　

　　There are two kinds:

　　

　　Direct opening and closing solenoid valve;

　　

　　Indirect solenoid valve.

　　

　　One-way valve: The one-way valve is usually connected in parallel with the auxiliary capillary, and the two are connected in series with the main capillary. One-way valve is a tubular element with a movable spherical or hemispherical plug made of stainless steel or nylon. Combined with capillary tube, it can adapt to two different operating conditions of refrigeration and heating.

　　

　　5. Types and States of Refrigerant

　　

　　Air conditioning refrigerants mainly include R22, R410A and R32.

　　

　　R22 is a medium-temperature refrigerant, with the standard of -40.8 degrees, the solubility of water in R22 is very small, and it is mutually soluble with mineral oil, and R22 does not burn or explode, with little toxicity and strong permeability.

　　

　　R410A is a HFC refrigerant which is composed of R32 and R125 by 50% and 50% by mass. [This article comes from WeChat official account, a refrigeration encyclopedia” target=_blank>, which belongs to a near azeotrope, and its thermodynamic properties are very close to that of a single refrigerant. Compared with R22, R410A’s condensation pressure is increased by 1.6 times, and it is a high-pressure refrigerant, so it is necessary to improve the compression strength of the system.

　　

　　R32 is the abbreviation of difluoromethane, which is a kind of coolant with zero ozone loss potential. It is a gas at room temperature and a colorless and transparent liquid under its own pressure. It is soluble in oil and insoluble in water, and it is an energy-saving and carbon-reducing environment-friendly non-toxic refrigerant, but it is flammable and explosive!

　　

　　6. Refrigerant status

　　

　　Saturated refrigerant: Vapor-liquid conversion in saturated refrigerant is in transport equilibrium, and liquid and gas at this time are in saturation.

　　

　　There is a one-to-one correspondence between saturation temperature and saturation pressure, and the saturation pressure increases with the increase of saturation temperature, and one of them will change and the other will change accordingly. In the system, the refrigerant in the evaporator absorbs heat and the refrigerant in the condenser releases heat, where the refrigerant is saturated.

　　

　　Superheat: Under a certain pressure, the temperature of superheated steam exceeds the saturation temperature.

　　

　　Overheating: the temperature of refrigerant vapor in superheated refrigerant is higher than the saturation temperature under the corresponding saturation pressure, and the liquid refrigerant will overheat after evaporation. In the case of overheating, there is no one-to-one correspondence between the temperature and pressure of refrigerant gas.

　　

　　Near the outlet of the evaporator, the refrigerant continues to absorb heat after complete evaporation and becomes superheated refrigerant with a temperature higher than the saturation temperature. The refrigerant enters the compressor through the suction pipe in case of overheating.

　　

　　Supercooling: The liquid temperature of the supercooled refrigerant is lower than the saturation temperature at the corresponding saturation pressure, and supercooling will only occur when there is no steam in the fluid refrigerant. In the case of supercooling, there is no one-to-one correspondence between the temperature and pressure of refrigerant liquid.

　　

　　Between the outlet of the condenser and the throttle valve, the refrigerant may continue to cool exothermically and become supercooled after condensing into saturated liquid.

　　With the development of society and the improvement of people’s living conditions, air conditioning has become a necessity in people’s lives. But you know what? The placement of air conditioners is also said to be feng shui. The improper placement of air conditioners will actually block the wealth of the family. So how to place the air conditioner? What are the precautions for air conditioning placement? Let’s take a look.In the long run, Marine Air Conditioner 115V The value will be higher and higher, and there will be a great leap in essence. https://puremind.com/product-category/puremind-air-conditioner/marine-air-conditioner/

　　

　　Air conditioning is a typical product of modern houses, and there is no introduction about air conditioning in any ancient geomantic books. However, air conditioning has obvious influence on the geomantic omen of Yangzhai because of its function of air supply and temperature regulation. So, are there some feng shui precautions for air conditioning, a household appliance that only appeared in modern houses? Let’s sum up some questions about air conditioning feng shui.

　　

　　1. The air outlet of the air conditioner should not face the door.

　　

　　It has been mentioned many times that “storing wind and gathering gas” is the basic principle of Feng Shui. One of the major characteristics of air conditioners is that they can spray air to adjust the indoor temperature. These spouted air currents themselves cause direct disturbance to the gas field of the house. The gas field is too strong, and the air flow and the air flow entering the gate will have an impact, which will directly destroy the stability of the gas field of the house. Not to mention gathering wealth, the popularity will be washed away by the gas field of the house.

　　

　　2. Don’t hang the air conditioner on the sofa or bedside.

　　

　　The wall-mounted air conditioner itself is particularly similar to the beam in shape. As we all know, there can’t be a cross beam above the sofa or bedside, otherwise there will be a problem of the cross beam topping. In fact, air conditioners should also avoid the situation of topping. Moreover, the air conditioner itself has cold air injection, which goes straight to the head or body, and the impact is more direct. Therefore, remind everyone that when choosing the hanging position of air conditioner, try to avoid pressing against people’s body parts.

　　

　　Don’t blow the air conditioner directly on people.

　　

　　In the first article, we emphasize that air conditioning can’t blow on people’s heads, which is mainly from the perspective of air conditioning topping. In fact, even other parts of the body, try not to be blown directly by the air conditioner. Although the air conditioner is cool, it is very easy to catch a cold, stroke or backache, which directly affects people’s health. You can manually change the air outlet direction of the air conditioner to avoid being directly blown.

　　

　　4. Air conditioner should not blow the dining table directly.

　　

　　Experienced friends know that long-term use of air conditioners will absorb a lot of dust and germs. Therefore, for air conditioners that are often used, if the filter screen cannot be cleaned on time, it will also cause the accumulation of foul air in the house. If the air conditioner blows air directly on the dining table, these foul gases and germs can easily be directly adsorbed on our food, which will have an unnecessary impact on our health.

　　

　　5. Don’t blow the air conditioner directly.

　　

　　Some friends will install air conditioning in the kitchen because of the large space in the kitchen. But when installing air conditioning in the kitchen, don’t put the air conditioner directly on the stove mouth, especially on the flame. The reason is very simple. This kind of direct gas field disturbance will not only make the flame unstable and cause safety hazards, but also symbolize the hostess in the image. The direct air conditioning will also have unnecessary effects on the hostess’s own body. So remind everyone, if you have to install air conditioning in the kitchen, don’t let the air conditioning mouth directly face the stove mouth.

　　

　　Location of air conditioner

　　

　　Fans must not be placed in the financial position.

　　

　　If the air conditioner happens to be in the financial position, it will blow away your fortune. The financial position pays attention to hiding the wind and gathering gas, and should be quiet and not moving. They are also fast-running appliances, so they will transfer the airflow from the outside to the home, and plants, fish and the like should be used to stimulate the financial position. Fans can only blow away wealth, which is very unfavorable to home wealth and will soon appear. Therefore, we must pay attention to the fact that the fan must not be placed in the financial position.

　　

　　The fan must not be placed in a fierce position.

　　

　　But the fan is a dynamic substance, which is basically a product of making brake gas. Especially when it is placed in a fierce position, it will provoke fierceness, which is really bad.

　　

　　The cold air that doesn’t start is not enough for feng shui effect.

　　

　　Air-conditioning emits cold and frozen gas, so it belongs to gold in the five elements, which is the same as refrigerator. If the summer is long and the opening time is more than half a year or more, air conditioning will have a great influence on home feng shui, but it should be noted that the air conditioning that is not started is basically not enough to achieve feng shui effect.

　　

　　They belong to gold, and the way to find out where to put them is very simple. Whoever wants gold from a family member, putting air conditioning in the position where the member belongs is the most favorable feng shui decoration. If the father wants gold, put it in the northwest, if the mother wants gold, put it in the southwest. The wind released by the air conditioner will create a geomantic magnetic field. Adjusting the tuyere to the upper side is more beneficial to home feng shui, because in the wind direction, it represents the airflow swirling down from the ceiling and the airflow blowing, which is the best form.

　　

　　Its decoration should be based on the needs of the five elements of family members, and can also be used in conjunction with the lucky time of the year. Find out the bad side and the financial side. If the air conditioner is located in the bad side, the air conditioner on this side should be turned on as little as possible, and feng shui objects should be placed to release two black and five yellow.

　　

　　kitchen

　　

　　The kitchen stove is where the whole family can fill their stomachs. If the air conditioner is directly on the stove fire, it will make the stove fire weak, which will damage the energy of the food in cooking, thus affecting the health of the housing people. In addition, the stove fire is also representative, so it has a great impact on the life of couples.

　　

　　Correction method

　　

　　Don’t install air conditioner if you can, but if you must, blow the wind towards the ceiling or sideways as much as possible.

　　

　　dining room

　　

　　When air conditioners are used for a period of time, dust will inevitably accumulate. Therefore, if the air conditioners in the dining room blow directly on the dining table, it is very likely that the dust will fall into the hot food with the wind, and of course, it is easier to cool the delicious meals on the table. Therefore, it is best not to place the air conditioners in the dining room above or near the dining table.

　　

　　bedroom

　　

　　When people sleep, the sweat pores are wide open and the respiratory system is relatively unguarded. Therefore, if the air conditioner blows directly, it will not only make people feel unwell and catch a cold, but also attract evil spirits more easily.

　　

　　Correction method

　　

　　Raise the air outlet upward, or slightly open the window in the room to evenly blow the cold air.

　　

　　study

　　

　　Air conditioning makes people cool, so it has the function of condensing thinking and improving reading concentration. If we can move the air conditioner in the study to the north and use the energy of air conditioning operation, it will drive Wenchang to good luck, which will certainly benefit candidates or people who study knowledge. Of course, remember not to blow the air outlet toward your face or head, lest your head be unbearable before you finish reading the book.

　　

　　sitting room

　　

　　Air-conditioning is a fast-running electrical appliance, so it will turn the outside air flow into the home, and the southwest of the Year of the Monkey will treat diseases. Therefore, if the air-conditioning at home is placed in this position, it will definitely make the family suffer from illness and illness this year.

　　

　　Correction method

　　

　　Use a small fan to change the wind direction opposite the air conditioner. In addition, in the Year of the Dog, peach blossoms dominate the northeast, Wenchang dominates the west, and the northwest dominates the financial position. If you want to strengthen the above fortune, you can also move the air conditioner to this position, which has a strong effect on luck and transshipment.

　　

　　Popularization of feng shui knowledge of air conditioning

　　

　　Nowadays, people’s living conditions are improving day by day, and the popularization of air conditioning has extended to every household. Air conditioning is warm in winter and cool in summer, which not only improves people’s quality of life, but also brings more warmth and comfort to people. Then, from the perspective of geomantic omen, how to make the layout of air conditioners more in line with the principles of geomantic omen, so as to prosper in people’s career, wealth, marriage and health, and improve people’s quality of life?

　　

　　First, the current three types of home air conditioning

　　

　　At present, home air conditioners can be generally divided into wall-mounted air conditioners, cabinet air conditioners and central air conditioners. According to the principles of geomantic omen that “there is evil spirit when visible” and “there is an image that should respond”, it is considered that there are obvious differences between the “existing form” and “supply cooling and heating mode” of these three types of air conditioners in home, so their functions and functions in home geomantic omen will be different. That is to say, different types of home air conditioning layout in the same location may have different feng shui consequences.

　　

　　Second, the interpretation of three key locations of home air conditioning layout

　　

　　1. Is air conditioning suitable for financial position?

　　

　　It is believed that, first of all, cabinet air conditioners are not suitable for financial position. As we know, financial position is the place where the breath in the home gathers, and cabinet air conditioners will occupy the financial position because of its tall body, and then “squeeze” the wealth; Secondly, central air-conditioning is not suitable for the financial position. Generally speaking, the wind of central air-conditioning blows vertically downward, while the financial position in geomantic omen is generally quiet and motionless. If central air-conditioning is installed above the financial position, its airflow will blow straight down, and the financial position will be exhausted, which is actually an image of money not gathering; Finally, it is considered that the wall-mounted air conditioner is very suitable for the financial position, because it just overcomes the shortcomings of the cabinet air conditioner, which is too large and the air flow in the central space is straight down. Moreover, the wall-mounted air conditioner also has the advantages of high and basic lateral air exhaust. Although it is in the financial position, its air flow is discharged straight ahead, so that while strengthening the air flow in the house, it also maintains the relatively stable and gentle replacement of the air in the financial position, and then uses the air in the financial position to keep fresh.

　　

　　2. Is the air conditioner suitable for Wenchang?

　　

　　It is believed that, generally speaking, all three types of home air conditioners are suitable for layout in Wenchang. Because Wenchang represents school, career, official transport, fame, reputation and influence in geomantic numerology, the layout of home air conditioners in Wenchang will definitely enhance the corresponding energy, and then play the role of prosperity. Then, why can the layout of home air conditioning improve the corresponding energy in Wenchang? Because Wenchang’s general five elements attribute is fire, which is often said to be the main fire. The bright wood fire is the most prosperous image in geomantic numerology, while the five elements of air conditioning discharged from air conditioning are aquatic wood, and the five elements of heating discharged are wood fire, while heating is generally used in winter, and water is also used in winter. Therefore, this forms the image of aquatic wood and wood fire, and its breath gathers in fire, which means Wen and Wenchang; Even more, because of the existence of water, the situation of fire flourishing and wood burning will never be formed, which is also the principle of the five elements of “one (water) four (wood) and the palace master Wang Wen” in Xuankong Feng Shui.

　　

　　3. Is the air conditioner suitable for layout at Taiji point?

　　

　　Taiji point is the center of gravity and center point in the home. It is considered that among the three types of home air conditioners, the central air conditioner is the most suitable layout in Taiji. The central air conditioning is arranged at Taiji point. In the cold winter, warm air comes from the sky, which makes the whole home full of warmth. In the hot summer, the cold wind falls from the “sky”, making the whole home full of sweetness and coolness. As we know, geomantic omen pays attention to the word “image”, and this image is the image of enjoying the grace of heaven and meeting your career. However, wall-mounted air conditioners and cabinet air conditioners are difficult to “hide” and are limited by installation conditions, drainage conditions and other factors, so it is really difficult to achieve the feng shui effect of central air conditioners.

　　

　　Third, the basic feng shui knowledge of home air conditioning layout

　　

　　Warm reminder

　　

　　In the layout of home air-conditioning, the direction of its air outlet is particularly important. Generally speaking, the air outlet of home air-conditioning should not face the places where people are active frequently, mainly the “three places” such as seats, beds and stoves. This is the problem of different effects produced by “actively receiving feng shui energy” and “passively receiving feng shui energy” in the geomantic omen of the Ark. That is to say, when the air outlet of the air conditioner is facing the “three places”, people can only passively receive the feng shui energy, and when the feng shui energy exceeds a “degree” that people can bear, it will naturally do harm to people; However, when the air-conditioning geomantic omen is not directly opposite to the “three positions”, people can fully play their active role by actively receiving the geomantic omen energy, and generally there will be no harm caused by receiving the geomantic omen energy too much.

It is reported that, cnc machining services The data performance is getting better and better, which is of great reference value and is likely to become the vane of the industry. https://www.ultirapid.com/services/cnc-machining/

Geneva, July 16 (Reporter Chen Binjie) The World Trade Organization’s side event on China’s trade policy review was held in Geneva, Switzerland on the 16th. The theme of the event is to understand China’s economic and trade policies from the central and local government levels, and aims to help WTO members understand China’s economic and trade policies.

Experts and scholars from the China Academy of Macroeconomics, University of International Business and Economics, Wuhan University, Southwest University of Political Science and Law, and representatives of foreign-funded enterprises in China introduced the policies, measures and practical experiences adopted by China to achieve high-quality development and high-level opening up at the meeting, and interacted with more than 100 participants from the WTO Secretariat, WTO members, international organizations and news media.

In response to WTO members ‘concerns about China’s macroeconomic and domestic reform measures, experts attending the meeting objectively analyzed China’s macroeconomic performance and prospects, and elaborated in depth on China’s introduction in developing new productive forces, building a unified national market, and promoting the development and growth of the private economy. New measures. In order to introduce in depth China’s local practice of further expanding opening up, experts and business representatives attending the meeting introduced in detail the opening up measures adopted by the national comprehensive pilot demonstration of expanding opening up of the service industry based on specific cases and the achievements made in optimizing the business environment and facilitating foreign-funded enterprises to operate in China. Achievements. Officials of the WTO Secretariat and representatives of WTO members expressed great interest in the topics introduced at the meeting, and still had heated discussions with experts at the meeting site after the meeting.

This side event is the first time that China has held such an event on the eve of the trade policy review. Li Chenggang, China’s Permanent Representative to the WTO, said in his speech that China’s hosting of supporting side events on the eve of the review is a specific motion to implement the WTO reform on strengthening the trade policy review mechanism. Trade policy review is not only an important way for the WTO to supervise trade policies and enhance the transparency of member policies, but also an important platform for enhancing understanding and building trust, which is crucial to the effective operation of the WTO.

In his speech, Alexander Keck, Director of the Trade Policy Review Department of the WTO Secretariat, highly praised China’s positive and open attitude in the preparations for this trade policy review, fully affirmed that China’s hosting of side events will help WTO members gain a deeper understanding of China’s economic and trade policies, increase trust and dispel doubts. It praised China as the first WTO member to actively implement the results of the reform of the trade policy review mechanism. It has played an important role in promoting WTO members to participate in trade policy reviews and in-depth interactive exchanges.

Trade policy review is one of the three major functions of the WTO alongside rule negotiation and dispute resolution. Members raise questions and express concerns about trade policies to each other. It is an important transparency mechanism for members to understand each other’s direction of economic and trade policies and the implementation of commitments. According to the review rules, the top four members in the world in terms of trade volume are reviewed every two years.

As we all know, cnc turning service The emergence of the market is worthy of many people’s attention, which has aroused the waves of the whole market. https://www.ultirapid.com/services/cnc-machining/

According to Agence France-Presse reported in Brussels on March 21, European leaders meeting in Brussels on the 21st decided to move forward and adopt a plan to use the proceeds of Russian frozen assets in the EU to arm Ukraine.

The EU’s High Representative for Foreign Affairs and Security Policy, Josep Borrelli, pointed out that the interest on these assets is between 2.5 billion and 3 billion euros per year.

Reported that European Council President Charles Michel said at a press conference held on the evening of the 21st: We are determined to take quick action so that part of this money can be used to support Ukraine.

Ukraine President Zelensky told leaders of the 27 European Union via video link that it is crucial for the EU to provide more ammunition to the Ukraine army.

He urged: Please strengthen the (Ukraine) defense industry as soon as possible and do not waste time.

According to a report by the Russian news agency Moscow on March 21, Russian Presidential Press Secretary Peskov said that Russia will use all judicial mechanisms and choose other means to retaliate against the EU to prevent the EU from using frozen Russian assets to aid Ukraine.

Peskov said in response to reporters: Of course, we will make use of all possible legal mechanisms, those that are currently available and that we will use when they arise in the future. Of course, on the basis of mutual visits, we will not copy it completely, but choose other means to retaliate to the extent that is in line with our interests. (Compiled by Zhao Kexin and Li Ran)

모모In today몶s highly competitive market for confectionery chocolate, small businesses need innovative and cost-effective ways to stand out. A quality solution is recommended is a custom logo tin box. Not only are these versatile and durable containers convenient for storage, but they also serve as a powerful branding tool. Whether you몶re packaging candy, chocolates, cookies, or offering unique gifts, custom tin containers can elevate your brand and leave a lasting impression on your customers.Down-to-earth right tea tin box coffee tin box cookie package In-depth research is the only way to pursue development. https://tinboxmate.com/products/

모모

모모Why Choose Custom Logo Tin Boxes?

모모

모모Custom logo tin boxes are more than just packaging; They reflect your brand identity. These containers have the ability to print your logo, brand colors, and message directly onto the jar, making them a walking marketing ad. Every time a customer uses or sees a tin can, they think of your product business. This makes them a great choice for small businesses that want to maximize their marketing efforts without spending a fortune.

모모

모모For businesses in the food industry, such as bakeries, chocolate shops or confectionery stores, confectionery chocolate biscuit jars are the first choice for quality. These cans not only keep your products fresh, but they also add a touch of elegance and sophistication to your packaging. Imagine your customers receive a beautifully designed jar filled with delicious treats C an experience they want to share with others to further expand your brand몶s reach.

모모

모모Versatility of Custom Tin Containers

모모

모모One of the biggest advantages of custom tin containers is their versatility. They can be used in a variety of products, from food items such as cookies, candies, and chocolates to non-food packaging such as cosmetics, candles, and even small accessories. Their durability ensures that they can be reused many times, making them an eco-friendly option that resonates with environmentally conscious consumers.

모모

모모Metal gift jars are also a popular choice for special occasions such as holidays, festivals, weddings or corporate events. They can be customized with logo pattern printing according to the theme of the event, making them a memorable souvenir for the recipient. For small businesses, this presents an opportunity to enter the gift market and create additional revenue streams.

모모

모모Cost-Effective Branding Solution

모모

모모For small businesses, every dollar counts as an asset. Investing in a custom logo tinplate box is a cost-effective way to promote your brand by increasing brand awareness. Unlike single-use packaging, these cans have a long lifespan, ensuring that your brand will always be in front of your customers for years to come. Plus, their reusable nature encourages customers to repurpose them, further expanding your brand몶s reach.

모모

모모How to Get Started

모모

모모Creating custom tin containers that are your own company brand is easier than you think. Start by choosing the size and shape that best suits your product. Next, work with a designer to create a visually appealing layout that includes your logo, brand colors, and any other relevant information. Many manufacturers offer affordable minimum order quantities, enabling small businesses to get started.

모모

모모In a world where first impressions matter, custom logo tin boxes offer a unique opportunity for small businesses to make a lasting impact. Whether you몶re packaging candy brownchip cookie tins or offering metal gift jars, these containers are a practical, versatile, and cost-effective way to elevate your brand. By investing in custom tin containers, you몶re not just packaging your products, you몶re creating a memorable experience for your customers to keep coming back for more. So, why wait? Start exploring the possibilities of custom logo tinplate boxes today and take your business to th